Fig Pro Audio

How to record bass DI plus amp tone at home

I play bass as well as guitar, and bass is the instrument where recording direct makes the most sense at home. A clean DI gives you a solid, even low end that's easy to mix. An amp, real or simulated, gives you the growl, grit and midrange that let the bass be heard on small speakers. Most bass tones you love on records are some blend of the two.

The catch is that two versions of the same bass part only blend well if they line up. Get that wrong and the low end goes thin and hollow, and it's easy to blame the amp, the bass or the strings when the real problem is timing. This guide covers how to record both, line them up and blend them.

Option 1: DI now, amp later (the easiest)

If you only have one instrument input, or you're not sure what amp tone you want yet, do this:

  1. Plug the bass into your interface's instrument (Hi-Z) input.
  2. Set the gain with your hardest playing, so the loudest notes peak well below the top of the meter.
  3. Record the DI on its own track.
  4. Duplicate the track, or send it to a second track, and put your amp plugin on the copy.

Because both tracks come from the same recording, they're already perfectly in time, and you can change the amp sound whenever you like. One thing to check: some plugins add a little processing delay. Modern DAWs compensate for that automatically (usually called plugin delay compensation), so leave that setting switched on.

This is the approach I'd recommend to most people starting out. You get the full DI-plus-amp sound with nothing to align.

Option 2: DI and a real amp at the same time

If you have a bass amp and want to capture it as you play, you need to split the signal: one path to the interface as a DI, one to the amp.

Now you have two tracks recorded at the same moment, but they won't necessarily be lined up. A mic in front of a speaker hears the sound slightly later than the DI, because sound in air takes about a millisecond to travel roughly a foot (34 cm). Even a few centimetres of distance shows up as a small delay.

Option 3: re-amping a DI through a real amp

Re-amping means sending a DI you've already recorded back out of your interface into a real amp, then recording the amp. It's a great way to try real amps on a finished part. It also introduces the biggest timing problem, because the signal makes a round trip out of the interface and back in, and comes back a few milliseconds late.

Sound On Sound puts it plainly: "a common mistake is the failure to realign the re‑amped track to the DI," and "Even a couple of milliseconds is enough to introduce comb filtering, which will thin out the bass sound when the re‑amped cab is combined with the DI" (Sound On Sound, "Mixing Metal").

Many DAWs have a tool that measures that round trip for you by sending a test "ping" out and timing its return. Check your DAW's manual for latency or round-trip measurement. Even then, measure again each session rather than trusting last time's number. Users on the REAPER forum report that the extra latency of a USB interface can be "slightly different each time" the device reconnects (Cockos forum). If your interface needs a re-amp box or a level adapter between its output and the amp's input, read the interface and amp manuals first so you don't send a line-level signal into an instrument input too hot.

Lining the tracks up

Whichever way you recorded, check alignment before you start mixing:

  1. Zoom right in on a clear, sharp note at the start of a phrase, ideally one where you played hard with nothing else ringing.
  2. Compare the start of the waveform on the DI and the amp track. If the amp track starts later, move it earlier until the first peaks line up.
  3. Look at the shape too. If one wave goes up where the other goes down, the tracks are in opposite polarity. Flip the polarity on one of them.
  4. Listen to the blend with both tracks at similar levels, and flip the polarity back and forth. The setting with the fuller, deeper low end is the right one.

Small nudges matter here. If your DAW lets you move a clip by samples rather than by grid steps, use that.

Blending them

With the tracks lined up, the blend is about giving each one a job:

A quick checklist

Get the alignment right and you'll find the blend does most of the work. The bass sounds both deep and clear, and you spend far less time fighting it with EQ.

Where FigAMP fits

Since version 1.3.1, FigAMP does Option 1 for you inside one plugin. Turn on Bass Mode (next to the Bright switch) and the amps and cabinets let a bass guitar's deepest notes through, down to a low B. Then turn up the Blend knob to mix your clean DI back in under the amp. FigAMP lines the two up in time and polarity internally, so there's nothing to align and no hollow low end. Around 40 to 60% Blend is a good starting point: more for a solid, modern bottom, less for a rawer amp sound.

Pick one of the two bass cabinets: the 4x10 is punchy with a growly upper midrange, and the 1x15 is deep and round. Every amp has a bass preset to start from. Black Panel - Bass Clean Thump is a clean, warm foundation, Brit 45 - Bass Rock Grit and Hot 20 - Bass Punchy Drive add classic rock growl, and Cali V - Bass Modern Grind and Steel 50 - Bass Metal Crunch are for heavier styles. The INPUT knob with its level light matches your interface, and Stereo/Mono keeps the bass mono in the mix.

If you'd rather keep the DI and the amp on separate tracks, set Blend to 0, put FigAMP on the copy, and use its Polarity switch when you blend them in your DAW. On the bass bus, FigSTRIP handles the bus compression. The FigAMP 14-day trial has every feature working, on Mac and Windows.